Bipolar transistors must be properly biased to operate correctly. In circuits made with individual devices (discrete circuits), biasing networks consisting of resistors are commonly employed. Much more elaborate biasing arrangements are used in integrated circuits, for example, bandgap voltage references and current mirrors. The voltage divider configuration achieves the correct voltages by the use of resistors in certain patterns. By selecting the proper resistor values, stable current levels can be achieved that vary only little over temperature and with transistor properties such as β.
The operating point of a device, also known as bias point, quiescent point, or Q-point, is the point on the output characteristics that shows the DC collector–emitter voltage (Vce) and the collector current (Ic) with no input signal applied.
Bias circuit requirements
A bias network is selected to stabilize the operating point of the transistor, by reducing the following effects of device variability, temperature, and voltage changes:
The gain of a transistor can vary significantly between different batches, which results in widely different operating points for sequential units in serial production or after replacement of a transistor. Due to the Early effect, the current gain is affected by the collector–emitter voltage. Both gain and base–emitter voltage depend on the temperature. The leakage current also increases with temperature.
A bias circuit may be composed of only resistors, or may include elements such as temperature-dependent resistors, diodes, or additional voltage sources, depending on the range of operating conditions expected.
Signal requirements
For analog operation of a class-A amplifier, the Q-point is placed so the transistor stays in active mode (does not shift to operation in the saturation region or cut-off region) across the input signal's range. Often, the Q-point is established near the center of the active region of a transistor characteristic to allow similar signal swings in positive and negative directions.
For digital operation, the Q-point is instead chosen so the transistor switches from the "on" (saturation) to the "off" (cutoff) state.
Thermal considerations
At constant current, the voltage across the emitter–base junction VBE of a bipolar transistor decreases by 2 mV (silicon) and 1.8 mV (germanium) for each 1 °C rise in temperature (reference being 25 °C). By the Ebers–Moll model, if the base–emitter voltage VBE is held constant and the temperature rises, the current through the base–emitter junction IB will increase, and thus the collector current IC will also increase. Depending on the bias point, the power dissipated in the transistor may also increase, which will further increase its temperature and exacerbate the problem. This deleterious positive feedback results in thermal runaway. There are several approaches to mitigate bipolar transistor thermal runaway. For example, Negative feedback can be built into the biasing circuit so that increased collector current leads to decreased base current. Hence, the increasing collector current throttles its source. Heat sinks can be used that carry away extra heat and prevent the base–emitter temperature from rising. The transistor can be biased so that its collector is normally less than half of the power supply voltage, which implies that collector–emitter power dissipation is at its maximum value. Runaway is then impossible because increasing collector current leads to a decrease in dissipated power; this notion is known as the half-voltage principle. The circuits below primarily demonstrate the use of negative feedback to prevent thermal runaway.
Types of bias circuit for class-A amplifiers
The following discussion treats five common biasing circuits used with class-A bipolar transistor amplifiers:
Fixed bias
Collector-to-base bias
Fixed bias with emitter resistor
Voltage divider bias or potential divider
Emitter bias
Fixed bias (base bias)
This form of biasing is also called base bias or fixed resistance biasing.
In the given fixed bias circuit,For a given transistor, Vbe doesn't vary significantly during use. And since Rb and the DC voltage source Vcc are constant, the base current Ib also doesn't vary significantly. Thus this type of biasing is called fixed bias.
The common-emitter current gain of a transistor (specified as a range on its data sheet as FE or ), allows us to obtain as well:Now Vce can be determined:Thus an operating point for a transistor can be set using Rb and Rc.
Advantages: The operating point is set by two resistors and the calculation is very simple.