Sue H. Elmore was a steamboat built for service on the coast of Oregon and southwest Washington. From 1900 to 1917, the vessel's principal route ran from Portland, Oregon down the Columbia River to Astoria, and then west across the Columbia Bar, then south along the Oregon coast to Tillamook Bay. Once at Tillamook Bay, Sue H. Elmore was one of the few vessels that could reach Tillamook City at the extreme southern edge of the mostly very shallow bay. After this Sue H. Elmore was sold, being operated briefly in Puget Sound under the name Bergen, and then for many years, out of San Diego, California as a tugboat under the name Cuyamaca. During World War II Cuyamaca was acquired by the U.S. Army which operated the vessel as ST-361. Afterwards the army sold ST-361 and the vessel returned to civilian ownership, again under the name Cuyamaca. In 1948 Cuyamaca sank in a harbor in Venezuela, but was raised and by the early 1950s, was owned by one A. W. Smith, of Pensacola, Florida. This vessel's former landing place in Tillamook, Oregon is now a municipal park named after the ship.
Design
Sue H. Elmore was built for the Pacific Navigation Company, which was closely linked to the S. Elmore Canning Company, with the wealthy businessman Samuel Elmore (1847-1910) being president of both concerns. The steamer was named after Samuel Elmore's eldest daughter. This vessel was generally called Elmore.
The intended use for the vessel was to establish regular steamship service between Tillamook, on the coast of Oregon, and Portland. Up until that time the bad navigation conditions at the entrance, called a "bar", to Tillamook Bay, had made it not always possible to make regular trips. The new steamer, generally called Elmore in practice, was designed by Capt. Paul Schrader (born 1850), who was also a stockholder in the Pacific Navigation Company. Sue H. Elmore was also intended replace of the company's former steamer, R.T. Elmore, which had been sold and taken to Alaska.
Schrader had over 20 years experience on the Tillamook route, and incorporated this experience into the design of the vessel. The steamer was "especially designed for barred harbor and coasting trade." The Elmore was intended to carry a big load of freight on a light draft on the shallow waters of Tillamook Bay. Elmore was also equipped to carry passengers. It was also built for service along the Oregon coast to the salmon-packing plants of the S. Elmore Cannery Co.
Construction
Construction was done at the shipyard of Joseph Supple in Portland, Oregon, where the keel for the new steamer was laid on May 15, 1900. Construction proceeded rapidly. The vessel was launched on Saturday, June 30, 1900, at 2:00 pm. Machinery still had to be installed. On July 9, 1900, the Elmore was towed downriver to the Willamette Iron Works for the boilers and machinery to be installed. There had been a delay in the construction at the Supple yard, which mean that the vessel could not be finished before August 1, 1900 at the earliest. Elmore was scheduled to make its trial trip on September 15, 1900, and Samuel Elmore came to Portland to be on board for the occasion.
Specifications
Dimensions
According to a news report in 1900, Sue H. Elmore was 100 feet long, 21 foot beam, with a maximum draft, when fully loaded, of 8 feet. The steamer measured out at 232 gross tons and 131 net tons. Tonnage was a measure of carrying capacity and not of weight. The official figures for the vessel were somewhat different, giving a length of 90.7 feet, beam of 23.8, and depth of hold of 8.0 feet. When unloaded ("light") Sue H. Elmore drew 5.5 feet of water forward and 8.0 feet aft. When loaded, the vessel drew 8 feet forward and 10 feet aft.
Machinery
The engine, built by Willamette Iron and Steel Works, was a fore and aft compound condensing type steam engine, with cylinder sizes of 10, 20 and 20 inches and a 20-inch stroke, generating 100 nominal horsepower and 300 indicated horsepower, could turn the propeller shaft at 125 revolutions per minute. The boiler installed in 1900 was larger than usual, and generated steam at 150 pounds of pressure. An electric lighting plant was installed. In 1919, if not before, the vessel was an oil-burner.
The ship had double steam winches mounted both fore and aft, cargo ports, and the latest freight handling machinery. Three life boats of a type then considered modern and improved were carried, as well as a life raft. The ship carried patent anchors, had an auxiliary schooner sailing rig, and was fitted with towing bits. Cruising speed downriver on the Columbia was said to have been easily maintained at 10 knots. The average speed however was stated in 1917 to be 9 knots.