The Heckler & Koch HK33 is a 5.56mm assault rifle developed in the 1960s by West German armament manufacturer Heckler & Koch GmbH (H&K), primarily for export.

Building on the success of their G3 design, the company developed a family of small arms (all using the G3 operating principle and basic design concept) consisting of four types of firearms: the first type, chambered in 7.62×51mm NATO; the second, using the Soviet 7.62×39mm M43 round; the third, chambered in .223 Remington and 5.56×45mm NATO; and the fourth type, chambered for the 9×19mm Parabellum pistol cartridge. Commercially the HK33 was a successful design but it did not sell as well as the G3.

Heckler & Koch HK33

The HK33 series of rifles were adopted by the Brazilian Air Force (Força Aérea Brasileira or FAB), the armed forces of Thailand and Malaysia where they were produced under a licence agreement. The rifle was also licence-built in Turkey by MKEK, and exported from France branded as MAS but actually made in Germany.

Heckler & Koch HK33

Design details

Operating mechanism

The HK33 is a selective fire weapon with Heckler & Koch's roller-delayed blowback system of operation. It employs a two-piece bolt consisting of a bolt head with a pair of rollers and bolt carrier. Upon firing, the two cylindrical rollers in the bolt head are cammed inward by inclined surfaces of the barrel extension and impart a rearward motion on the locking piece, which also propels the bolt carrier rearward. This built-in mechanical disadvantage delays the movement of the bolt head relative to the bolt head carrier which is withdrawing at significant higher velocity of the bolt head. The rollers soon compress entirely into the bolt head, clearing the locking recesses of the barrel extension, and both parts now continue rearward together, opening the breech and actuating the extraction and feeding cycles. The chamber is opened under high pressure, thus the chamber received a series of flutes in order to increase extraction reliability and prevent sticking of the spent casing to the chamber walls.

Heckler & Koch HK33

The G3 roller-delayed blowback mechanism designed around 7.62×51mm NATO ammunition was downsized and revised for reliably using 5.56×45mm NATO ammunition. This required changing geometrical transmission ratio relationships between parts. Based on the geometric relationship arising from the angles of the roller contact surfaces of the locking piece and the barrel extension recesses, the recoil of the bolt head is delayed by a ratio of 3:1 for the 5.56×45mm NATO chambering. Thus during the same period of time, the bolt head carrier moves 3 times faster than the bolt head. This ratio is continued until the locking rollers have been withdrawn from the barrel extension recesses.

Like the G3 bolt the HK33 bolt features an anti-bounce mechanism that prevents the bolt from bouncing off the barrel's breech surface. The "bolt head locking lever" is a spring-loaded claw mounted on the bolt carrier that grabs the bolt head as the bolt carrier group goes into battery. The lever essentially ratchets into place with friction, providing enough resistance to being re-opened that the bolt carrier does not rebound. The spring-powered claw extractor is also contained inside the bolt while the lever ejector is located inside the trigger housing (actuated by the recoiling bolt). Further like the G3 the HK33 also contains a spring extractor and a buffer. The ejector lever was installed in the trigger housing and is actuated by the recoiling bolt.

The reliable functioning of roller-delayed blowback mechanisms is limited by specific ammunition and arm parameters like bullet weight, propellant charge, barrel length and amount of wear. For obtaining a proper and safe functioning parameters bandwidth Heckler & Koch offer a variety of locking pieces with different mass and shoulder angles. The angles are critical and determine the unlock timing and pressure curve progression as the locking pieces act in unison with the bolt head carrier.

Features

The HK33 is a modular weapon system. Its butt-stock, fore-stock and pistol-grip/fire-control assembly may be changed at will in a variety of configurations (listed below). Simple push-pins hold the components in place and removing them will allow the user to remove and replace parts rapidly. The rifle is disassembled into the following components for maintenance: the receiver/barrel, stock with return spring, bolt assembly and trigger pack in pistol grip.