Timiș 2 were a series of tram vehicles built in Timișoara, Romania, initially by the Timișoara Transport Company, and later by Electrometal Timișoara (also known as Eltim).
Trams
The tramcars appeared in the late 1960s as part of the desire of the Timisoara Transport Executive (Intreprinderea de Transport Timisoara) to locally produce and buy trams. Previously the transport company acquired Electroputere Craiova's V54 type trams in 1955 and Bucharest Transport Executive (Intreprinderea de Transport Bucuresti) Main Workshops' V56 and V58. These were only imported vehicles, however, and were not great in number, as Timisoara still operated trams made from the pre-WW2 era. The first attempt at producing a tram locally was the Gb 2/2 in 1948 and 1954, but only 7 units were made. The next attempt was the Timiș 1 tramcars (official classification was T1-62), which were built only in a limited series in 1962. Between 1965 and 1967 the transport executive considered introducing a series of articulated tramcars, named TA-65, but this plan was soon abandoned due to engineering challenges related to the radius of the curves. The planners then turned to an easier alternative: a motor car-trailer car solution. Thus in 1969 the TM 69E prototype, the "pioneer" of the Timis 2 was made. Trials with this unit led to the production of a trailer car as well starting from July 1970, being officially tested on 1 December 1970, and in 1971 the project was approved for mass production. Mass production started in 1972.
Over the years the tramcar underwent modifications. In 1974 the manufacturing passed from using Kiepe Electric combined power handles to locally made Eltim ones. In 1975 the tram was used for the first time outside Timisoara, examples reaching Oradea, Braila and Galați. In 1977 production was transferred to Electrometal Timișoara after the Transport Executive's ownership of the tramcar factory was revoked. Starting with 1981, production for metre gauge tram networks commences. In 1982 a major facelift is added to the base model and at around the same time, an articulated prototype, named Eltim V2(C) was produced. Starting with 1985 it entered in severe competition with the articulated V2A and V3A trams made by the Bucharest Transport Executive's Main Workshops. Production of the model stopped in 1990, with 541 motor cars and 531 trailer cars produced, at the same time when the V2A and V3A production stopped.
Soon after the downfall of communism in Romania, these tram cars began to be retired. Sibiu was the first city to phase them out in 1994, even though the fleet was only 7 years old at the time. More cities followed, and in Timișoara these trams were retired in 2005. The last town that retired these passenger cars was Cluj, in August 2011, thus ending the era of Romanian-made tramcars from the communist times.
Technicalities
The project was led by engineer Gheorghe Bihoi. The construction of this tram is simple, being parallelepipedical-shaped and made out of welded metal. It had 2 simple headlights and the destination display varied by city and year of manufacture. It had 3 doors, the middle one being double folding and the 1st and 3rd door being simple folding.
Internally the drivers cabin was separated from the passenger compartment. In the drivers cabin, apart from the driving controls and door switches, a megaphone for the passenger compartment was included, so the tram driver could communicate to the passengers.
The passenger interior varied for the motor car and trailer car. At 5 passengers/m², 61 people could fit in the motor car and 76 in the trailer car. At 8 passengers/m², 98 people would fit in a motor car and 122 in a trailer car. Initially both the motor car and the trailer car had 24 seats. Illumination was provided by 6 tubes of neon lighting. Ventilation was done not only naturally, through hatches placed on the roof that could be opened, but also through "heaters" (aeroterme), where air from the outside would be introduced into the inside of the tramcars, with the help of 4 "heaters" placed under the seats. In the cold winters, they would recirculate air and heat it up.
The trucks/bogeys were made by the Grivița Auto Repair Works (I.R.A. Grivița), which at the time was producing axles for trams. The power was supplied by 2 axle-mounted traction motors, giving a combined output of 240 kW. In the case of networks that had 600 V DC electrification networks instead of the 750 V DC electrification network, the output of these motors was reduced to 190 kW, combined. Separated, these traction motors would have a power output of 120 kW and 95 kW, respectively.