A vertical stabilizer or tail fin is the static part of the vertical tail of an aircraft. The term is commonly applied to the assembly of both this fixed surface and one or more movable rudders hinged to it. Their role is to provide control, stability and trim in yaw (also known as directional or weathercock stability). It is part of the aircraft empennage, specifically of its stabilizers.

The vertical tail is typically mounted on top of the rear fuselage, with the horizontal stabilizers mounted on the side of the fuselage (a configuration termed "conventional tail"). Other configurations, such as T-tail or twin tail, are sometimes used instead.

Vertical stabilizer

Vertical stabilizers have occasionally been used in motor sports, with for example in Le Mans Prototype racing.

Vertical stabilizer

Function

Principle

The vertical tail of an aircraft typically consists of a fixed vertical stabilizer or fin on which a movable rudder is mounted. A trim tab may similarly be mounted on the rudder. Together, their role is to enable trim in the yaw direction (compensate moments in yaw generated by any asymmetry in thrust or drag), enable the aircraft to be controlled in yaw (for example, to initiate side slip during a crosswind landing), as well as provide stability in yaw (weathercock or directional stability).

Vertical stabilizer

The greater its position away from the center of gravity, the more effective the vertical tail can be. Thus, shorter aircraft typically feature larger vertical tails; for example, the vertical tail of the short Airbus A318 is larger than that of its longer counterparts in the A320 family.

The effectiveness of the vertical tail depends on its efficiency and the vertical tail volume coefficient (also called volume ratio), which non-dimensionalizes its area and arm with the dimensions of the main wing:

(where the indices v and w stand for vertical tail and wing respectively, S stands for area, and L_w is typically the mean aerodynamic chord). Values for the vertical tail coefficient vary only mildly from aircraft one type of aircraft to another, with extreme values ranging from 0.02 (sailplane) to 0.09 (jet aircraft transport).

The tail efficiency is the ratio of the dynamic pressure at the tail to that in the freestream. The tail has its maximum capability when immersed in the free stream with an efficiency of one. When partially immersed in a wake its effectiveness is reduced because the wake has a lower dynamic pressure than the free stream. The fin height may need to be increased to restore its required effectiveness in certain flight conditions. The Panavia Tornado had a tall fin for directional stability at high angles of incidence.

Trim and control in yaw

The rudder is the directional control surface and is usually hinged to the fin or vertical stabilizer. Moving it allows the pilot to control yaw about the vertical axis, i.e., change the horizontal direction in which the nose is pointing.

Maximum rudder deflection is usually controlled by a rudder travel limiter. The largest achievable angle of a rudder at a particular flight condition is called its blowdown limit. It represents a balance between the aerodynamic forces on the rudder and the mechanical forces from the actuating mechanism.

Multi-engined aircraft, especially those with wing-mounted engines, have large powerful rudders. They are required to provide sufficient control after an engine failure on take-off at maximum weight and cross wind limit and cross-wind capability on normal take-off and landing.

For taxiing and during the beginning of the take-off, aircraft are steered by a combination of rudder input as well as turning the nosewheel or tailwheel. At slow speeds the nosewheel or tailwheel has the most control authority, but as the speed increases the aerodynamic effects of the rudder increases, thereby making the rudder more and more important for yaw control. In some aircraft (mainly small aircraft) both of these mechanisms are controlled by the rudder pedals so there is no difference to the pilot. In other aircraft there is a special tiller controlling the wheel steering and the pedals control the rudder, and a limited amount of wheel steering (usually 5 degrees of nosewheel steering). For these aircraft the pilots stop using the tiller after lining up with the runway prior to take-off, and begin using it after landing before turning off the runway, to prevent over correcting with the sensitive tiller at high speeds. The pedals may also be used for small corrections while taxiing in a straight line, or leading in or out of a turn, before applying the tiller, to keep the turn smooth.