Dental cements have a wide range of dental and orthodontic applications. Common uses include temporary restoration of teeth, cavity linings to provide pulpal protection, sedation or insulation and cementing fixed prosthodontic appliances. Recent uses of dental cement also include two-photon calcium imaging of neuronal activity in brains of animal models in basic experimental neuroscience.
Traditionally cements have separate powder and liquid components which are manually mixed. Thus working time, amount and consistency can be individually adapted to the task at hand. Some cements, such as GIC, can come in capsules and are mechanically mixed using rotating or oscillating mixing machines. Resin cements are no cements in a narrower sense, but rather polymer based composite materials. ISO 4049: 2019 classifies these polymer based luting materials according to curing mode as class 1 (self-cured), class 2 (light-cured), or class 3 (dual-cured). Most of the commercially available products are class 3 materials, combining chemical- and light-activation mechanisms.
Ideal cement properties
High biocompatibility - zinc phosphate cement is considered the most biocompatible material with a low allergy potential despite the occasional initial acid pain (as a consequence of inadequate powder/liquid ratio) Non irritant. Polycarboxylate cement is considered the most sensitive type due to the properties of PAA. Antibacteria properties to prevent secondary caries Provide a good marginal (bacteria-tight) seal to prevent marginal leakage. Resistant to dissolution in saliva, or other oral fluid – a primary cause of decementation is dissolution of the cement at the margins of a restoration. High strength in tension, shear and compression to resist stress at the restoration-tooth interface. High Compressive strength (minimum 50 microns acc. to ISO 9917-1) Adequate working and setting time. Good aesthetics. Good thermal insulation properties as a liner under metal restorations Opacity – for diagnostic purposes on radiographs. Low film thickness (maximum 25 microns acc. to ISO 9917-1). Low allergy potential Low shrinkage Retention – if an adhesive bond occurs between the cement and the restorative material, retention is greatly enhanced. Otherwise, the retention depends on the geometry of the tooth preparation.
Cements based on phosphoric acid
Dental cements based on organometallic chelate compounds
Dental applications
Dental cements can be utilised in a variety of ways depending on the composition and mixture of the material. The following categories outline the main uses of cements in dental procedures.
Temporary restorations
Unlike composite and amalgam restorations, cements are usually used as a temporary restorative material. This is generally due to their reduced mechanical properties which may not withstand long-term occlusal load. GIC – Glass Ionomer cement Zinc Polycarboxylate cement Zinc Oxide Eugenol cement RMGIC
Bonded amalgam restorations
Amalgam does not bond to tooth tissue and therefore requires mechanical retention in the form of undercuts, slots and grooves. However, if insufficient tooth tissue remains after cavity preparation to provide such retentive features, a cement can be utilised to help retain the amalgam in the cavity.
Historically, zinc phosphate and polycarboxylate cements were used for this technique, however since the mid-1980s composite resins have been the material of choice due to their adhesive properties. Common resin cements utilised for bonded amalgams are RMGIC and dual-cure resin based composite.
Liners and pulp protection
When a cavity reaches close proximity to the pulp chamber, it is advisable to protect the pulp from further insult by placing a base or liner as a means of insulation from the definitive restoration. Cements indicated for liners and bases include: Zinc oxide eugenol Zinc polycaroxylate RMGIC Pulp capping is a method to protect the pulp chamber if the clinician suspects it may have been exposed by caries or cavity preparation. Indirect pulp caps are indicated for suspected micro-exposures whereas direct pulp caps are place on a visibly exposed pulp. In order to encourage pulpal recovery, it is important to use a sedative, non-cytotoxic material such as Setting Calcium Hydroxide cement.
Luting cements
Luting materials are used to cement fixed prosthodontics such as crowns and bridges. Luting cements are often of similar composition to restorative cements, however they usually have less filler meaning the cement is less viscous. RMGIC GIC Zinc Polycarboxylate cement Zinc oxide eugenol luting cement