The NZASM 32 Tonner 0-4-2RT of 1894 was a South African steam locomotive from the pre-Union era in Transvaal.
In 1894 and 1897, the Nederlandsche-Zuid-Afrikaansche Spoorweg-Maatschappij of the Zuid-Afrikaansche Republiek (Transvaal Republic) placed four rack tank locomotives with a wheel arrangement in service on the rack section between Waterval Onder and Waterval Boven. Since the railway classified its locomotives according to their weight, these engines were known as the .
Waterval Onder to Waterval Boven
The construction of the railway line from Delagoa Bay to Pretoria was beset with difficulties, both in terms of disease and engineering. Malaria claimed many lives among the construction crews and some of the terrain was mountainous. In the Elandspruit valley, where the Elands River formed a waterfall, the adjacent cliffs presented a natural barrier to the continuation of the railway from the Eastern Transvaal Lowveld up to the Transvaal Highveld.
In terms of construction, the climb up the escarpment was arguably the most difficult section on the route to be encountered by the railway builders. When the line reached Waterval Onder, they had a choice between a lengthy detour with sharp curves and costly deep cuttings, embankments and viaducts to comply with the agreed upon gradient of 1 in 50 (2%), or a shorter section, which would entail a gradient of 1 in 20 (5%) over a distance of in one place, as well as a tunnel.
The shorter and steeper route was selected. While a gradient of 1 in 20 (5%) is not insurmountable by light trains with orthodox adhesion locomotives, safety and economical considerations led to the decision to install a rack track on the steep section up the escarpment between Waterval Onder and Waterval Boven. The rack track was built to the Riggenbach system which was in use on European mountain railways, with the rack laid between the rails.
The Riggenbach rack system used a ladder rack, formed of steel channels connected by square rungs at regular intervals, to engage the pinion wheels of the rack engine. The rungs of the NZASM rack track were spaced apart. To ensure correct meshing of the gears when entering the rack section, engaging pieces of special section, long and fitted with round-bar rungs, were hinged to each end of the rack, supported by a spiral spring underneath. When the rack engine made contact with the hinged section and the gear wheels did not mesh with the rack correctly, the engaging section would be pressed down until correct meshing was accomplished.
Manufacturer
The line from Delagoa Bay and up the escarpment to Waterval Boven was completed on 20 June 1894. To work on the rack section, the Nederlandsche-Zuid-Afrikaansche Spoorweg-Maatschappij (NZASM) ordered three 0-4-2 rack tank locomotives from Emil Kessler's Maschinenfabrik Esslingen. The three locomotives were delivered in 1894, numbered in the range from 991 to 993. A fourth locomotive, no. 994, was ordered in 1897 and was identical to the other three, except that it had a coal bunker and water tanks with larger capacities, which made it heavier. Since the NZASM classified its locomotives according to their weight, the rack locomotives were known as . In addition to being numbered, they were all named as well, with the names and numbers cast in brass and mounted on their tank sides.
Characteristics
The rack locomotive had plate frames, arranged outside the coupled wheels, and was equipped with the Heusinger von Waldegg version of Walschaerts valve gear. The pinion for the rack was mounted between the coupled wheels, just forward of the driving axle. The pinion axle was coupled to the drivers through side rods, with the connecting rods coupled directly to crank disks which were mounted on the ends of the axle, outside the frames. These crank disks were grooved to act as brake drums.
A second free-turning pinion wheel which also meshed with the rack, was mounted on the leading driving axle. It had grooved brake drums bolted to each side and acted as a brake only, with the brakes being applied by a hand mechanism from the footplate. The brakes on the driving and free-turning pinion wheels were separately controlled, while the vacuum brake gear on the engine was only used to control the brakes of the train.