Bicon Dental Implants is a privately owned company located in Boston, MA. The company specializes in short dental implants that use a locking taper or cold welding connection to secure the abutment to the implant. Bicon is notable and worthy of mention for the following three reasons: First, Bicon implants are extremely short in length. The size of Bicon implants allow them to be placed in regions that are crowded with natural teeth and/or implants, or in regions that would otherwise require bone grafting. Second, the implants do not have the screw-form design typical of other available implants. Third, the abutments are connected to the implant via a locking taper. This is notable from both a medical and engineering standpoint as no other implant company offers an implant with a biological seal at the implant/abutment interface; almost all other implants possess an internal screw to connect their abutments.

History

Bicon has been in operation since June 1994. Prior to Bicon, its main product line was under the ownership of two other entities, Driskell Bioengineering (1985–1987) and Stryker Corporation (1988–1994) of Kalamazoo Michigan. The following section briefly describes the history of the Bicon company and the dental implant products that it offers.

Bicon Dental Implants

Vietnam War

The style of implant offered by Bicon can trace its provenance to the Battelle Memorial Institute in Columbus, Ohio, where in 1968 the US Army Medical Research and Development Command Dental Research Division funded a project aimed at developing prosthetics to address the influx of craniofacial injuries sustained by personnel in the escalating Vietnam War.

Bicon Dental Implants

Research performed by the implant's inventor, Thomas Driskell, showed that a multi-finned plateau design more effectively distributed occlusal forces to the underlying bone as compared to contemporary screw form implants. Using rhesus monkeys as an experimental animal, Driskell et al. were able to demonstrate direct bone-to-implant contact in the plateau style implant, a process called osseointegration. Furthermore, the implant designed by Driskell possessed a sloping shoulder that, in later years, would be shown to play a role in the maintenance of crestal bone height and a natural looking interdental papillae.

Bicon Dental Implants

With the advent of the 1970s, renewed interest in the use of ceramics began to develop. In 1975, Driskell et al. unveiled the Synthodont implant, an implant made of high density aluminum oxide (Al2O3). Unlike other conventional screw-type implants, the Synthodont implant design incorporated the use of the “fins” that had proved so successful in the U.S. Army project.

1970s–1980s

In the late 1970s, following the initial successes of the Synthodont implant, Driskell et al. introduced the Titanodont implant. The Titanodont implant was composed of surgical grade titanium (grade 5, Ti-6Al-4V). The Titanodont implant was unique for three main reasons. First, the Titanodont implant allowed for complete interchangeability with abutments of varying diameters and angles. This interchangeability allowed for a more natural biological width. Second, the implant was grit blasted and acid etched, which provided both a larger surface area and preferable substrate for cells involved in osseointegration. Third, and perhaps most importantly, the Titanodont implant had a locking taper abutment connection, which allowed 360° of abutment positioning, along with a bacterial seal. Unlike screw-form implants, the locking taper connection design prevents the infiltration of bacteria into the implant crypt and surrounding tissues.

1980s–1990s

In the mid-1980s, Driskell and his partners formed a company called DB Bioengineering. DB Bioengineering received pre-market notification in October, 1985 for the implant Driskell and his team had developed at Batelle – now known as the DB Precision Fin Implant System. Two short years later, in 1987, DB engineering – along with the DB Precision Fin Implant System – were sold to the multinational conglomerate, the Stryker Corporation. At this juncture, the DB Precision Fin Implant System possessed the qualities that separated it (along with modern Bicon implants) from its competitors: a sloping shoulder, specialized titanium instrumentation, and a slow speed drilling system. Slow speed drilling was included in order to prevent the thermal damage induced by the high speeds conventional drilling.