The family of Walker railmotors were a type of diesel railcar operated by the Victorian Railways in Australia.
After World War II, the Victorian Railways undertook a major rebuilding program known as Operation Phoenix. One of the first tasks was the upgrading of passenger services on country branch lines, through the replacement of 23 wooden-bodied railmotors built in the 1920s, and the withdrawal of steam locomotive hauled mixed trains.
An initial order of twelve railcars, six railcars with trailers, and twelve railcars was placed with Walker Brothers, Wigan, England. It was then extended to include a further ten railmotors and trailers. The first was delivered in 1948, with additions to the fleet running through to 1955.
Construction
The power units and controls were built by Walker Bros. and shipped out from Wigan England, the underframes were built by Thompsons of Castlemaine and the car bodies were built by Martin & King, in the Melbourne suburb of Armadale. Assembly took place at the Newport Workshops. The van bodies were constructed with composite wood and steel framework, and aluminium sheeting screwed to the frames.
The engine and trailing units were initially fitted with small plates below skirt level identifying each section as part of that specific railmotor set, i.e. 80RM, but these were removed as units were rotated through workshops and mixed with each other. Within a few years the identity of the and motors was marked only on the cabside door (with nothing on the saloon unit), and on the railmotors only on one side of each motor unit with nothing on either saloon unit. Vehicle identities were occasionally further confused when cabside doors were swapped in later years.
The intended life of the Walker railmotors was only 10 years. However, most remained in service for up to 30 years.
102hp & 153hp
The final fleet included 13x engine/driving units 1-13RM and 16x engine/driving units 20-35RM which looked similar; these shared 27x trailing units each mounted on only one bogie, and attached semi-permanently to the associated motor unit, leaving one motor unit of each type spare. The trailing units were not identified normally when in service, but some correspondence notes individual identities No.100 to No.111 (or No.101 to No.112) and No.220 to No.234. This was marked on a small plate on the passenger/driver door of cabs.
The passenger units were all identical with room for 18 1st class and 22 2nd class seated passengers plus 2 tons luggage, except for 100, 104 and 220, which had 18+27 seats and room for only 1.27 tons of luggage; their tare weight was a ton less than the rest of the fleet.
Newsrail April 1982 records the small-van units as "11, 12 and 20", and coupled to 3RM as of 8 June 1976, and 31RM as of 1 January 1977.
280hp
Separate to the paired units, railmotors 80-92RM consisted of two driving/sitting units, one either side of the power unit that gave its identity to the full consist. Originally, 80-91RM were in service and 92RM was spare without attached driving/passenger units.
One unit in each pair was fitted with seating for 38 1st class passengers, and the other had 56 2nd class passengers, for a total of 94 seats. Each was also capable of holding a single ton of luggage, the train crew only were permitted to walk through the centre motor unit engine room.
Unlike the and variants, the driving/passenger units of the series were classed A880-A891 for the 1st class units, and B880-B891 for the 2nd class units. While possible, there's no reason to assume that the sets were broken up or shuffled around, besides the central motor section.
Trailers
To go with the Walker railmotors, sixteen trailer cars were built. The first were delivered as class RMT, numbers 50 and 51; they were reclassed to MT in 1949, and further deliveries brought the class up to 64MT.
Each was mounted on two bogies with no driving stands, so they required a runaround at terminal stations. Stylistically, they matched the and railcars, and were a little shorter than the type.
Each trailer had capacity for 16 1st, 22 2nd seated passengers and 2 tons of luggage, except 55MT fitted with 38 2nd-class seats instead of a mixture.
Like the motors, these trailers were not fitted with standard couplings so special arrangements had to be made when it was necessary to move one of the trailers with a normal locomotive.
In Service
The first run was on 15 March 1948, between Heathcote and Wallan on the North Eastern line; this was with , 1RM. The first unit ran from Spencer Street to Daylesford, until that roster was taken by the first of the units - 80RM - on 6 June 1950.