An atmospheric water generator (AWG), is a device that extracts water from humid ambient air, producing potable water. Water vapor in the air can be extracted either by condensation - cooling the air below its dew point, exposing the air to desiccants, using membranes that only pass water vapor, collecting fog, or pressurizing the air. AWGs are useful where potable water is difficult to obtain, because water is always present in ambient air.

AWG may require significant energy inputs, or operate passively, relying on natural temperature differences. Biomimicry studies have shown the Stenocara gracilipes beetle has the natural ability to perform this task.

Atmospheric water generator

History

The Incas were able to sustain their culture above the rain line by collecting dew and channeling it to cisterns for later distribution. Historical records indicate the use of water-collecting fog fences. These traditional methods have usually been completely passive, employing no external energy source and relying on naturally occurring temperature variations.

Atmospheric water generator

Air wells are one way to passively collect moisture from air.

Atmospheric water generator

Brine extraction technology was contracted by the US Army and the US Navy from Terralab and the Federal Emergency Management Agency (FEMA).

DARPA's Atmospheric Water Extraction program that aims to develop a device which can provide water for 150 soldiers and be carried by four people. In February 2021 General Electric was awarded 14 million dollars to continue development of their device.

In 2022, a cellulose/konjac gum-based desiccant was demonstrated that produced 13 L/kg/day (1.56 US gal/lb/day) of water at 30% humidity, and 6 L/kg/day (0.72 US gal/lb/day) at 15% humidity.

Technologies

Cooling-based systems are the most common, while hygroscopic systems are showing promise. Hybrid systems combine adsorption, refrigeration and condensation.

Cooling condensation

Condensing systems are the most common technology in use.

A cooling condensation type AWG uses a compressor to circulate refrigerant through a condenser and then an evaporator coil that cools the surrounding air. Once the air temperature reaches its dew point, water condenses into the collector. A fan pushes filtered air over the coil. A purification/filtration system keeps the water pure and reduces the risk posed by ambient microorganisms.

The rate of water production depends on the ambient temperature, humidity, the volume of air passing over the coil, and the machine's capacity to cool the coil. AWGs become more effective as relative humidity and air temperature increase. As a rule of thumb, cooling condensation AWGs do not work efficiently when the ambient temperature falls below 18.3 °C (65 °F) or the relative humidity drops below 30%. The cost-effectiveness of an AWG depends on the capacity of the machine, local humidity and temperature conditions, and power costs.

The Peltier effect of semiconducting materials offer an alternative condensation system in which one side of the semi-conducting material heats while the other side cools. In this application, the air is forced over the cooling fans on the side that cools which lowers the air temperature. The solid-state semiconductors are convenient for portable units, but this is offset by low efficiency and high power consumption.

Potable water generation can be enhanced in low humidity conditions by using an evaporative cooler with a brackish water supply to increase the humidity. A special case is water generation in greenhouses because the inside air is much hotter and more humid. Examples include the seawater greenhouse in Oman and the IBTS Greenhouse.

In dehumidifying air conditioners, non-potable water is a by-product. The relatively cold (below the dewpoint) evaporator coil condenses water vapor from the processed air.

When powered by coal-based electricity it has one of the worst carbon footprints of any water source (exceeding reverse osmosis seawater desalination by three orders of magnitude) and it demands more than four times as much water up the supply chain than it delivers to the user.

The most efficient and sustainable method is to use an adsorption refrigerator powered by solar thermal, particularly useful in desert climates due to the abundance of sunlight. The captured waste heat can be used to further efficiency by pumping the collected water to a storage site.

Hygroscopy

Hygroscopic techniques pull water from the air via absorption or adsorption. These materials desiccate the air. Desiccants may be liquid ("wet") or solid.

Wet desiccants

Liquid desiccants include lithium chloride or lithium bromide.